|
|
RapidDiver.com has donated over $30,000 worth of dive equipment to qualifing dive rescue teams. If you are a dive team and you would like some assistance in raising funds to buy rescue equipment, please contact me at the email address below. If you would like to help fund a Rescue Dive Team you can simply click on the ChipIn link. Thank you in advance for your support. Chris@RapidDiver.com Here are the Rapid Diver FAQS: 1. When was the Rapid Diver developed by whom and who were the first users? The Rapid Diver was developed/invented (holds Patent and Trademark) by Christopher De Felice in early 2002 and Orange County Sherriffs Dept was the first operation to deploy the units. If you are a manufacturer and would like to license the Rapid Diver technology contact Chris@RapidDiver.com. We take patent and trademark infringement seriously. If you know of any possible infringement please report it to: Legal@RapidDiver.com 2.How much time do you get underwater with the Rapid Diver? The physics are the same. An average diver breathes about 1 cu ft per minute. The standard tank for professional use is the 27 cu ft steel tank. We have reports of 30+ minutes in 30 feet or less. Please report you air consumption times on your posts! 3.Is the Rapid Diver "Made in America"? Yes, the Berry Amendment Rapid Diver Tactical is made in the USA. 4.Is the Rapid Diver "Universal fit"? Yes it is. 5. How long does the Rapid Diver take to deploy. With the straps pre-adjusted the unit takes less then 15 seconds from duffel to don. 6. Where can I buy a Rapid Diver Tactical/Responder? The Rapid Diver Tactical and Responder are sole source from the www.SubSeaTactical.com . NOTE: Only the Rapid Diver Sport (not approved for professional use) is available through the Zeagle dealer network. 7. What do you recommend for Public Safety Divers As you know the PSD community is very specialized depending on their particular region of the country. I follow NFPA 1670: Standard on Operations and Training for Technical Rescue. The Rapid Diver has secured its niche in the PSD community because rescue professionals have unique requirements and unfortunately limited budgets and space to store their equipment. One of the challenges in creating the Rapid Diver system for rescue work was to make a unit that would be compact enough to store in the rescue vehicle, be big enough to do the job and still be cost effective. My goal was to have the entire system fit into a Pelican case ready to dive. Here are my suggestions, Gas management, alternate air source, and bottle size: I highly recommend the steel tanks either 27 cu ft as standard equipment for PSD use. These 27 cu ft tanks are the biggest tanks available for the Rapid Diver system. The steel tank has very favorable trim characteristics and we have had reports of over 30 minute bottom times in 30 feet or less. Like cave diving doctrine, I lean towards the rule of thirds. Most rescue scenerios should be in the 10-minute range, after that the situation moves towards recovery. Other configurations: 1. The Back Pad is designed to hold a tank (80 cu ft) on the back. When configured this way the back tank becomes primary and the front is back up. Most dive scenarios involve removing occupants of boats and vehicles. Keeping the back clean of obstructions is especially useful when entering a vehicle underwater. The option of having a back mount tank on the Rapid Diver is advantageous if the situation calls for additional bottom time. Redundant air options for the Rapid: 1. A 6 cu ft tank can be attached to the front tank bands beneath the tank. We have a special adapter for simple attachement of a 6 cu ft tank or a 13 cu ft tank below the main tank. 2. A 6 cu ft tank or 13 cu ft tank can also be used in a drop leg configuration off of the gear belt with our special gear belt. 3. A Router box with LP quick connects can be attached on the tank. This configuration gives maximum redundancy because it allows you to connect any available air supply including surface supplied. 4. Or....Side mount the tank/s. Simple side mounting is very effective with Rapid Diver. The side mount configuration allows you to still keep the back free but still have the extra cu ft (80 alums work well). The Rapid Diver is tactical in nature; you can configure the unit depending on the situation. Environmental exposure: I dive with a dry suit approx. 6 months a year and they work great with the Rapid Diver. There are many fairly inexpensive quick donning front entry dry suits available. |
|